Products brief introduction
HC series of portable water chillers are designed to be either air-cooled or water-cooled. This series of water chillers has been designed for use with water at temperature between 7-30° C with ± 1° C deviations, and provides cooling capacity from 6, 800-120, 000 kcal/hr.
Specail Features
*Adopt the top-quality and up-to-date designed compressors, circulating pumps and fans imported from Europe, USA, save electricity and durable in operation.
*Equipped with entirely up-to-date designed radiator excellent efficiency in heat exchanging.
*Equipped with open-type stainless steel water tank, quite easy to clean and maintain.
*Equipped with precise electronic temperature controls, which can accurately measure and precise control temperature ± 1° C.
* Equipped with a sensitive alarm and controls(including amp-overloading alarn, high and low voltahe and electronic delay-timer protective equipments)while breakdown happens, the equipment will give the alarm and display the cause of the breakdown immediately.
Note:
*The standard voltage is3Φ , 380V, 50Hz.
*Refer to the weight of plastics and cooling capacity to select the HC series industrial chiller.
*Have any special needs, please contact us.
*Please excuse for not note if some specifications of products are changed.
Refrigeration capacity is tested under the condition:
*That cold water oulet temperature is at 15° C.
*That colded water inlet temperature is at 30° C.
*That colded air temperature is at 35° C.
| Model |
Unit |
HC-03ACI(E) |
HC-05ACI(E) |
HC-08ACI(E) |
HC-10ACI(E) |
HC-12SACI(E) |
HC-15SACI(E) |
| Cooling capacity |
kW |
8 |
14 |
23.7 |
30 |
37 |
42 |
| kcal/h |
6800 |
12040 |
20450 |
24080 |
32000 |
36120 |
| Compressor |
type |
All-close scroll |
| power |
kW |
2.5 |
4.4 |
3×2 |
4.4×2 |
10.5 |
4.4×3 |
| Refrigerant |
type |
R22(R407C/R134A) |
| Evaporator |
type |
Water tank immersion |
Shell evaporator |
| Air cooled condenser |
type |
Finned condenser |
| fan power |
kW |
0.25 |
0.6 |
0.45×2 |
0.6×2 |
0.6×2 |
0.6×3 |
| Pump |
power |
kW |
0.75 |
1.5 |
3 |
| flow |
L/min |
83 |
208 |
330 |
| Water tank capacity |
Liter |
100 |
260 |
160 |
| Flow water inlet and outlet pipe inch |
Inch |
1 |
1.5 |
2 |
| Diminsions (LxWxH) |
mm |
1250×800×1470 |
1250×800×1470 |
1750×800×1470 |
1750×850×1470 |
1750×850×1470 |
2500×850×1470 |
Water-cooled industrial chiller specifications
| Model |
Unit |
HC-03WCI(E) |
HC-05WCI(E) |
HC-08WCI(E) |
HC-10WCI(E) |
HC-12SWCI(E) |
HC-15SWCI(E) |
| Cooling capacity |
kW |
9 |
15 |
25 |
32 |
40 |
48 |
| kcal/h |
7580 |
13500 |
21150 |
28000 |
34000 |
41000 |
| Compressor |
type |
(All-close scroll) |
| power |
kW |
2.5 |
4.4 |
3×2 |
4.4×2 |
10.5 |
4.4×3 |
| Refrigerant |
type |
R22(R407C/R134A) |
| Evaporator |
type |
Water tank immersion |
Shell evaporator |
| Water cooled condenser |
type |
Shell condenser |
| Chill water flowrate |
L/min |
≥36 |
≥60 |
≥100 |
≥135 |
≥160 |
≥200 |
| Pump |
power |
kW |
0.75 |
1.5 |
3 |
| flow |
L/min |
80 |
208 |
330 |
| Water tank capacity |
Liter |
80 |
200 |
150 |
| Chilled water inlet and outlet pipe inch |
Inch |
1 |
1.5 |
2 |
Flow water inlet and outlet pipe inch
|
inch |
1 |
1.5 |
2 |
| Diminsions (LxWxH) |
mm |
1200×800×1250 |
1500×800×1200 |
1800×800×1400 |
2000×800×1400 |
Hydraulic System:
1. The double proportional compound valve control system pressure & flow, highly sensitive & stable
2. Imported high quality Pump, low in noise, long in lifespan & stable in performance
3. World-famous servo hydraulic system optional, better performance in lower noise & energy saving
4. The precise feedback control of servo system to the pressure & flow, with higher sensitivity & more accurate repeatability precision
5. High performance hydraulic valve, less failure, fast switch, convenient maintenance
6. Low pressure mold protect system, which is more suitable for the precise mould
7. Greese & lubrication oil in dependent lubrication system can lubricate everywhere in the best situation
ustrial ZElectrical System:
1. Control by double CPU, the system HMI use X86 300MHz technical grade display. The system employees a RISC 140MHz microprofessor, with high speed, noise-immunity, fan-less and lower power consumption, independent control structure improve the stablity of control
2. 8.4" display screen with resolution 800*600, user friendly screen & optional choose of language
3. Equiped with USB(2.0) port & ethernet(100-base T) ports
4. 32 Points input & output, entendable and trouble spot can be replaced easily
5. Linder transducer's resolution is 1/65535, more precise in control
6. 120 technological parameters access can be stored & uploaded with an ordinary USB drives
7. Injection End and temperature tracking is curve display, dynamic recorder parameter is modified, dynamic warningis exhibited, all these make the operation more convenient.
Servo Controller Part:
1. High Precise Control The servo system can control the machine's pressure, speed & location precisely, make sure that the error of accurate repeatability precision for the shot measurement is <0.3%
2. High sensitive response Because the motor vector is matched with the controller accurately, it only takes 0.5sec. inputing the number from 0 to max. Compared with other traditional hydraulic injection molding machine, HJ series is more faster in speed with shorter cycle time and high efficient in production
3. Low noise Compared with traditional fixed pump & variable pump system, the noise is 1/10 lower under normal circumstance, more suitable for sealed dustless workshop
4. Energy Saving Overall efficiency is 10% more & driving capacity is 18% more than common machine. This series can save 40-80% energy, and achieve first-class energy efficency
5. Water cooling saving The system condition prevent high pressure uploading without any power output, leads to the water cooling saving
| Parameter |
Unit |
HJF118-F5 |
| Screw diameter |
mm |
A |
B |
C |
| 35 |
38 |
40 |
| Screw I/D ratio |
L/D |
23.9 |
22 |
20.9 |
| shot volumn (theoretical) |
Cm3 |
154 |
181 |
201 |
| injection weight(PS) |
g |
141 |
165 |
183 |
| injection rate |
g/s |
80 |
95 |
105 |
| injection pressure |
Mpa |
219 |
186 |
167 |
| screw speed |
r/min |
0~220 |
| clamp force |
KN |
1180 |
| opening stroke |
mm |
340 |
| space between tie bars (W*H) |
mm |
370*370 |
| max mould height |
mm |
400 |
| min mould height |
mm |
150 |
| ejector stroke |
mm |
100 |
| ejector force |
KN |
33 |
| ejector number |
PC |
5 |
| max pump pressure |
Mpa |
16 |
| pump motor power |
KW |
11 |
| heating power |
KW |
6.5 |
| machine dimension |
M |
4.2*1.25*1.8 |
| machine weight |
T |
3.5 |
| oil tank capacity |
L |
210 |
FAQ
Q1. What is the warranty for the injection molding machine
A1:Total 18 month,Included machine platen,base,injection unit,clamping unit.
Q2:Can you sending engineer to oversea install machine and trainning customer's workers.
A1: Yes,We will send engineer to customer factory install the machine or trainning customer's workers. in one week,total free.
After one week, 50$ per day
Q3:How Many spare parts you will prepare for customer?
A3: Spare parts included: mould clamp, long and short nozzle,heating band,Wrench,Switch,Thermocouple,Operation manual
Tool box,Lubricate Oil,Sealing,Filter etc.
Q4:Computer sytem,Except English, can you change other language,say: French,Spanish,Arabic,Russian.
A1:Yes,when you place order,please tell us the language which you required. Standard one with English,Japanese,Chinese,Korea.
Q5:Can you change the power source for us? Say:we need 3 Phase 220V 60HZ
A5: When you place order,please write clearly.Then we will change the electric system for you.
Q6:If i Need Green Color machine,can you do it for us?
Q7: Yes,please give us the color sample.So we can do it for you.
Ningbo Haijiang Machinery Manufacturing Co.,Ltd.
Address:Next to the treasure Bringing the road, Yinzhou District, Ningbo (Tong Indone)
){kind=link}